【英文标准名称】:Germanstandardmethodsfortheexaminationofwater,wastewaterandsludge-Generalmeasuresofeffectsandsubstances(groupH)-Part7:Determinationofacidandbasecapacity(H7)
【原文标准名称】:德国对水、废水和淤泥检验的标准方法.效应和物质的一般量度(H组).第7部分:酸碱度的测定(H7)
【标准号】:DIN38409-7-2004
【标准状态】:作废
【国别】:德国
【发布日期】:2004-03
【实施或试行日期】:
【发布单位】:德国标准化学会(DIN)
【起草单位】:
【标准类型】:()
【标准水平】:()
【中文主题词】:水质试验;效应量度;物质量度;废水检验;试验报告;试验;酸;滴定法;解释;pH值;数学计算;碱;酸度;水化学;定义;标准方法;化学分析和试验;分析;分析方法;污泥检验;污泥;污染控制;污水;水
【英文主题词】:
【摘要】:
【中国标准分类号】:Z16
【国际标准分类号】:13_060_50
【页数】:27P;A4
【正文语种】:德语
基本信息
| 标准名称： | 双圆锯裁边机 |
| 英文名称： | Double edger |
| 中标分类： |
农业、林业 >>
农、林机械与设备 >>
锯材、人造板机械与设备 |
| 替代情况： | 原标准号ZB B97016-1986 |
| 发布部门： | 国家林业局 |
| 发布日期： | 2000-11-10 |
| 实施日期： | 2001-02-01 |
| 首发日期： | 1900-01-01 |
| 作废日期： | 1900-01-01 |
| 归口单位： | 全国人造板机械标准化技术委员会 |
| 起草单位： | 全国人造板机械标准化技术委员会 |
| 出版社： | 中国标准出版社 |
| 出版日期： | 2004-04-22 |
| 页数： | 平装16开 |
| 书号： | 155066.2-13523 |
适用范围
本标准规定了双圆锯裁边机主参数、分类、技术要求、试验方法、检验规则、标志、包装、运输、贮存。本标准适用于锯片间距为610～4500mm的纵向、横向和联合人造板双圆裁边机。
前言
没有内容
目录
没有内容
引用标准
没有内容
所属分类： 农业 林业 农 林机械与设备 锯材 人造板机械与设备
Product Code:SAE J1930
Title:Electrical/Electronic Systems Diagnostic Terms, Definitions, Abbreviations, and Acronyms--Equivalent to ISO/TR 15031-2
Issuing Committee:Vehicle E E System Diagnostic Standards Committee
Scope:SCOPE - PurposeThis SAE Recommended Practice supersedes SAE J1930 Apr 2002, and is technically equivalent to ISO 15031-2. Thisdocument is applicable to all light-duty gasoline and diesel passenger vehicles and trucks, and to heavy-duty gasolinevehicles. Specific applications of this document include diagnostic, service and repair manuals, bulletins and updates,training manuals, repair data bases, underhood emission labels, and emission certification applications.SAE J1930 Revised Proposed Draft SEP2008 - 3 -This document should be used in conjunction with DAE J1930-DA Digital Annexes, which contains all of the informationpreviously contained within the SAE J1930 tables.These documents focus on diagnostic terms applicable to electrical/electronic systems, and therefore also containsrelated mechanical terms, definitions, abbreviations, and acronyms.Even though the use and appropriate updating of these documents is strongly encouraged, nothing in these documentsshould be construed as prohibiting the introduction of a term, abbreviation, or acronym not covered by these documents.Certain terms have already been in common use and are readily understood by manufacturers and technicians, but donot strictly follow the methodology of this document. The J1930 committee may approve these terms that already may beconsidered industry standards. These terms fall into three categories:a. Acronyms that do not logically fit the term.b. Acronyms existing at the component level, i.e., their terms contain the base word or noun that describes the genericitem that is being further defined.c. Acronyms for terms that appear to contain the base word, but are frequently used as a modifier to another base word.(This use may possibly be thought of as following the methodology since the acronym is normally used as a modifier.)